2019 Infiniti M35 V6-3.5L (VQ35HR) Diagnostic and Repair Information Page 578
performing the next test.
- GO TO 2.
2.CHECK ATF TEMPERATURE
With CONSULT-III
1. Start the engine.
2. Select "ATF TEMP 1" in "Data Monitor" in "TRANSMISSION".
3. Check ATF temperature is in the following range.
ATF TEMP 1: 20锟斤拷C (68锟斤拷F) - 140锟斤拷C (284锟斤拷F)
With GST
1. Start the engine.
2. Drive vehicle for approximately 5 minutes in urban areas.
Is ATF temperature within specified range?
YES - GO TO 3.
NO - Drive vehicle to warm ATF or stop engine to cool ATF.
3.CHECK SYMPTOM (PART 1)
With CONSULT-III
1. Select "1ST GR FNCTN P0731" in "DTC & SRT confirmation" in "TRANSMISSION".
2. Drive vehicle with manual mode and maintain the following conditions.
GEAR: 1
ACCELE POSI: 0.7/8 or more
VEHICLE SPEED: 10 km/h (7 MPH) or more
3. Keep the current driving status for 2 seconds or more if CONSULT-III screen changes from "OUT OF CONDITION" to "TESTING".
CAUTION:
When "TESTING" is not indicated on CONSULT-III for a long time, check "Self Diagnostic Results" in "TRANSMISSION". When a
DTC other than "P0731" is detected, check the DTC. See: Diagnostic Trouble Code Descriptions/DTC Index/TCM.
With GST
1. Drive vehicle and maintain the following conditions for 2 seconds or more.
Selector lever: "M" position
Gear position: 1st
Accelerator pedal opening: 0.7/8 or more
Vehicle speed: 10 km/h (7 MPH) or more
2. Check DTC.
Is "OUT OF CONDITION", "STOP VEHICLE" or "COMPLETED RESULT NG" displayed? / Is "P0731" detected?
YES-1 - "OUT OF CONDITION": Perform "Step 3" again.
YES-2 - "STOP VEHICLE": GO TO 4.
YES-3 - "COMPLETED RESULT NG": Go to See: P Code Charts/P0731/7AT RE7R01A.
YES-4 - "P0731" is detected: Go to See: P Code Charts/P0731/7AT RE7R01A.
NO - Check intermittent incident. See: Testing and Inspection/Initial Inspection and Diagnostic Overview/How to Perform Efficient Diagnosis
For an Electrical Incident.
4.CHECK SYMPTOM (PART 2)
With CONSULT-III
1. Stop vehicle.
2. Drive vehicle in "D" position allowing it to shift from 1GR to 7GR and check shift timing and shift shock.
- INSPECTION END
Diagnosis Procedure
1.CHECK INTERMITTENT INCIDENT
See: Testing and Inspection/Initial Inspection and Diagnostic Overview/How to Perform Efficient Diagnosis For an Electrical Incident.
Is the inspection result normal?
YES - Replace A/T assembly. See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and Repair/Removal and
Replacement/7AT RE7R01A/Transmission Assembly/Exploded View.
NO - Repair or replace damaged parts.
5AT RE5R05A
P0732 2GR INCORRECT RATIO
Description
This malfunction is detected when the A/T does not shift into 2GR position as instructed by TCM. This is not only caused by electrical
malfunction (circuits open or shorted) but by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.
On Board Diagnosis Logic
- This is an OBD-II self-diagnostic item.
- Diagnostic trouble code "P0732" with CONSULT-III or 19th judgment flicker without CONSULT-III is detected when TCM detects any
