Disclaimer Infiniti G35x Sedan AWD V6-3.5L (VQ35DE) Technical Service Bulletin # 04-038 Date: 040820
Brakes - On-Car Brake Rotor Resurfacing
Classification:
BR04-008
Reference:
ITB04-038
Date:
August 20, 2004
INFINITI:
ON-CAR BRAKE ROTOR RESURFACING
APPLIED VEHICLES:
All Infiniti
If YOU CONFIRM:
A vehicle needs to have the brake rotors resurfaced (front or rear)
ACTION:
Use the ProCut(TM) PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin.
^ The ProCut(TM) PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing.
^ The ProCut(TM) PFM Series brake lathe can be ordered from TECH-MATE.
186
^ ProCut(TM) technical support or service can be obtained by calling 1-800-543-6618.
NOTE:
Brake rotors may need to be resurfaced during routine brake repair or for brake judder incidents.
^ Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the
brake rotors (see ITB00-024).
TIPS FOR USING THE PROCUT(TM) PFM SERIES ON-CAR BRAKE LATHE
^ Read and follow all instructions contained in the Technical Manual provided with your ProCut(TM) equipment.
^ The ProCut(TM) brake lathe also comes with an instructional video that can be used as a training aid.
^ Additional training is available from your local ProCut(TM) representative by calling 1-800-543-6618.
A. Make sure the cutting tips are sharp in good condition and installed "right-side" up.
^ Make sure to use ProCut(TM) brand tips.
^ The cutting tip UP side has a groove or letters.
NOTE:
A tip mounted upside-down will produce a surface finish that looks like an old LP record.
^ Each cutting tip has three cutting corners. Rotate or replace the tip as needed.
NOTE:
You should get at least 7 cuts per corner. However tip life is affected by variables such as rust or ridges. In order to determine when to
rotate Ups monitor the rotor finish. If the rotor finish begins to look inconsistent or feels rough to the touch tips should be rotated or
replaced. Tips that are chipped or cracked should never be used.
B. For best accuracy stabilize (firmly support) the vehicle with a jack or jack stand as shown in Figure 1.
^ On some hoists the vehicle may wobble a little while using the on-car brake lathe. Not good.
CAUTION:
Any rocking motion (wobble) of the vehicle during the ProCut(TM) automatic compensation procedure will reduce the accuracy of the
resurfacing.
^ If wobble occurs during the rotor resurfacing process/procedure the finished rotor runout may be more than factory specification and
should be checked before using the rotor.
C. Prevent metal shavings from contacting or collecting on the ABS speed sensors.
^ Remove any shavings that stick to the ABS speed sensor's magnet. It is best to clean the ABS sensor with the rotor removed.
D. After a rotor has been resurfaced with the ProCut(TM) brake lathe:
187
^ If the rotor must be removed for any reason mark the exact location (rotor to axle hub) before removing the rotor (see Figure 2).
^ The rotor must be reinstalled back to the same location.
E. Do not tighten the wheel lug nuts with an air impact driver.
^ Use a torque wrench to tighten the lug nuts to the proper torque specification.
^ Uneven or high torque applied to the lug nuts may distort (warp) the brake rotor and hub. This may increase rotor runout and cause
excessive rotor thickness variation as the rotor wears.
CLAIMS INFORMATION
Please reference the current Infiniti "Warranty Flat Rate Manual" and submit your claim(s) using the Operation Code (Op Code) or combination of
Op Codes that best describes the operations performed.
