2017 Infiniti G37 Sedan V6-3.7L Diagnostic and Repair Information # 10-012A Date: 110616
A/T - 7 Speed A/T Fluid Checking And Filling Information
Classification: TE09-002A
Reference: ITB10-012A
Date: June 16, 2011
ESSENTIAL TOOL; J-49829 7 SPEED A/T FILL PUMP
This bulletin has been amended. The Title and ATF Level Check procedure have been amended. Please discard previous versions of this bulletin.
APPLIED VEHICLES:
All Infiniti vehicles with 7 Speed A/T using Nissan MaticS ATF
SERVICE INFORMATION
When filling up checking the ATF level or if the pan of a RE7R01 series 7 speed automatic transmission has been drained or removed a special tool
must be used.
Page 155
^ This special tool is the"Transmission Fill Pump" J-49829.
^ This special tool is considered "Essential" and was sent to each dealer on January 19, 2010. Your Non-Vehicle account will be charged the
introductory price of $177.85 plus applicable taxes and freight.
^ For proper use of this tool go to ATF Level Check.
CAUTION:
Fill the Transmission Fill Pump with new Nissan MaticS ATF (999MP-MTS00P) only. Never fill with any other fluid.
ATF Level Check
1. Park the vehicle on a lift and set the parking brake.
2. Connect CONSULT III (C-III) to the vehicle.
3. With C-III monitor ATF temperature.
NOTES:
> ATF temperature must be maintained at 95-113锟斤拷F (35-45锟斤拷C) during ATF level check.
> If the ATF temperature is above 113锟斤拷F stop the engine to allow the ATF to cool down.
4. Once the ATF temperature reaches approximately 04锟斤拷F (40锟斤拷C) or below start the engine and let idle.
5. Shift the shift selector lever (shift lever) in each gear position and then return to Park.
6. Raise the vehicle on the lift.
NOTE:
Leave the engine idling. If the engine is turned off, the ATF fluid level will be adjusted well below the proper level.
Page 156
7. Remove the overflow plug from the transmission pan (see Figure 1).
^ Have a drain pan positioned under the overflow plug hole.
^ At first an initial amount of fluid may come out. This does not mean the transmission is full.
NOTE:
The engine MUST BE IDLING the whole time during the fluid level check. If the engine is turned off, the ATF fluid level will be adjusted well
below the proper level.
IMPORTANT:
In order to make sure the transmission is full; you must overfill the transmission and then let the excess drain out from the overflow plug hole.
8 Connect the Transmission Fill Pump at the overflow plug hole (see Figure 2).
9. Pump in approximately 2 liters (about 2 quarts) of Nissan MaticS ATF.
10. Disconnect the Fill Pump hose at the quick disconnect (see Figure 2).
^ If a steady stream of fluid drains out go to the next step.
IMPORTANT:
The amount of fluid that drains out should be enough so that it is obvious the fluid was overfull and is now draining to the correct level.
NOTE:
The engine MUST BE IDLING the whole time during the fluid level check. If the engine is turned off, the ATF fluid level will be adjusted well
below the proper level.
^ If little or no fluid drains out repeat Step 8 and 9.
Page 157
11. Allow fluid to drain from the overflow tube until it is just a drip.
NOTE:
Check to make sure the fluid temperature is still in specified range (35-45锟斤拷C 95-113锟斤拷F).
12. Install a new overflow plug. This completes the ATF level check.
^ Torque the filler plug to 12.4 Nm (1.3 kg-m 9 ft lb).
Refill After Draining / Removing the Pan
1. With the pan and drain plug installed connect the Transmission Fill Pump at the overflow plug hole and then fill the pan with approximately 4
liters (about 4 US quarts) of Nissan Matic S ATF.
2. Perform ATF Level Check.
